Audit, Implementation, Measurement and Verification. From energy audits to real results.
Wednesday 28 October 2026
An energy audit can identify opportunities to reduce costs, improve efficiency and address problems with farm equipment. But producing the audit report is only part of the process.
This article highlights how energy audits, supported implementation and then a verification process helped farms to improve efficiency and secure other benefits.
Experience from Queensland Farmers’ Federation’s (QFF) energy audit programs suggests three things are particularly important:
- Understanding the farm system,
- Supporting implementation, and
- Verifying what happens afterwards.
Start with the farm system
Energy and water use are integral to farm productivity. A good energy audit starts by understanding how the farming system needs to perform, then considers how energy can be used most effectively to deliver that outcome.
A Sunshine Coast dairy’s irrigation system had very poor distribution uniformity, with some areas receiving little or no water. The audit considered two upgrade options: the cheaper option also had the shorter payback, but the farm selected the more substantial upgrade.
Importantly, the selected system was expected to use more electricity because the objective was to improve irrigation performance, not simply minimise energy consumption. Measurement and verification (M&V) showed that annual electricity use increased by only 541 kWh, compared with the 2,000 kWh increase estimated in the audit. At the same time, pumping efficiency improved from 6.83 to 5.0 kWh/ML/m, distribution uniformity increased from 13.9% to 62.2%, and pumping time fell from about 403 to 220 hours to deliver the same volume of water. The improved irrigation performance was also expected to increase dry matter production by around 18 tonnes per year, while the ability to operate two sprinkler lines at once almost halved the labour required for irrigation.
The result illustrates why energy and water efficiency need to be considered together. The upgraded system used slightly more electricity overall, but used that energy more effectively to deliver water where it was needed, leading to greater production.
Supporting the farm to implement
An audit recommendation is not necessarily a ready-to-build project.
At the Mareeba Hay Farm, the audit identified solar, changes to pumping operations, automation and tariff options. Discussions between the farmer, auditor, pump shop and electrician helped determine how the system should work in practice. The farm subsequently implemented solar PV, a variable speed drive, automation and a tariff change.
The benefits were not limited to energy and cost. In a later conversation, the farmer explained that remote operation of the pump from a phone also removed the need to drive down to the creek pump to switch it manually, including at night when she would otherwise have needed to take her daughter with her. It was a practical improvement to the way the farm, and the family, operated.
This implementation stage matters. Recommendations may interact, equipment options may change and the farm still needs to decide how different measures work together.
M&V is part of the continuous improvement process.
Measurement and verification is not simply a final check against the energy audit. It continues the process by measuring what actually happened, understanding differences between the expected and actual results, and identifying opportunities for further improvement.
At an Atherton Tablelands cropping farm, purchased electricity fell from 189 to 96 kWh per megalitre, reducing electricity cost from around $41 to $21/ML. M&V also identified substantial solar exports and recommended moving more irrigation into solar-generation hours where practical.
A similar result was found at an Ipswich Nursery. Its solar system delivered 17% greater energy savings than forecast, but financial savings were 45% lower because much of the generation was exported and the feed-in tariff was lower. M&V identified a further opportunity to increase solar self-consumption by shifting suitable loads into daylight hours.
These examples show that M&V should not simply ask if the audit got it right. It should also ask “What did we learn and what should the farm do next?”
In several of these projects, verification confirmed substantial benefits while also identifying additional savings that could still be captured. In others, it helped demonstrate benefits that were not adequately described by energy savings alone, including productivity, labour and how the farming system operated.
That makes M&V part of a continuous improvement process, rather than the end of an energy project.
A useful approach is therefore:
- Understand the whole farm system.
- Support implementation by working with the farm and advisors to prioritise and implement the actions.
- Verify the outcomes and keep looking for the next improvement.